H-2WP

二音路造型喇叭

H-2WP

H-2WP 專為戶外應用而設計，是一款圓頂形小型表面安裝 2 分頻揚聲器，可確保高品質的聲音重現。揚聲器角度可平行於安裝面360度調整。（但是，對於牆壁安裝，請將揚聲器面朝下，左右各傾斜在 45 度以內。）

2 路設計揚聲器
鐵磁流體冷卻平衡球頂高音揚聲器、釹磁錐低音揚聲器
狹窄的覆蓋區域可實現可控的聲音
聲音方向可在360° 範圍內調整
120 W 的高功率處理能力（連續程序）
防火ABS 外殼(UL 94-V0)
防風雨 IP64 認證

規格 A&E規格下載

外箱型式

Sealed type

額定輸入

12 W (16 Ω, high impedance)

輸入功率

120 W (continuous program/4 Ω), 40 W (continuous pink noise/4 Ω)

額定阻抗

4 Ω, 16 Ω
100 V line: 830 Ω (12 W), 1.7 kΩ (6 W), 3.3 kΩ (3 W)
70 V line: 420 Ω (12 W), 830 Ω (6 W), 1.7 kΩ (3 W), 3.3 kΩ (1.5 W)

輸出音壓電平

88 dB (1 W, 1 m) at installation in 1/2 free sound field
(Measured by installing the unit in the center of a wall.)

頻率響應

100 Hz - 20 kHz

喇叭組成

Low frequency: 10 cm cone-type, High frequency: Balanced dome-type

輸入端子

Detachable screw terminal, (+)/(-) 2 each (for bridging connection)

使用電纜線

Solid cable, stranded cable: 0.2 - 2.5 mm² (AWG No. 24 - 14 equivalent)

Dust/Water Protection

IP64

安裝環境

Indoor installation, under-eave installation(*1)

工作溫度

-10 °C to +50 °C

外觀

Punched net: Steel plate (zinc plating), white, powder coating
Frame: Fire-resistant ABS, white, paint
Base frame: Stainless plate

尺寸

Ø268 x 111 mm

重量

2.1 kg (including base frame)

附屬品

Base frame x 1, Electrical box mounting screw x 1 set

Recommended Electrical Box

1-gang type (with cover)(*2)

Other Feature

Angle of speaker: 360 degrees adjustable in parallel to the mounting surface. (The angle should be kept within 45 degrees left and right each in a downward direction for the wall installation)

(*1) Avoid installing the speaker in locations close to the seashore or in indoor swimming facilities that are not well ventilated. In such locations, the bracket may be vulnerable to corrosion, eventually allowing the speaker to fall resulting in personal injury.
(*2) Without using an electrical box, mounting the supplied base frame directly to a wall or ceiling allows the speaker installation.

請下載資料以獲取完整規格。

The loudspeaker shall be a two-way, sealed enclosure suitable for wall or ceiling mounting with an external appearance that is aesthetically pleasing and blends well with surrounding building architecture and fixtures. Loudspeakers requiring visible external mounting brackets shall not be acceptable. The loudspeaker shall utilize high quality components. The high frequency component shall be a 1" balanced dome tweeter; Ferrofluid-cooled for high power handling, The low frequency component shall be a 4” cone woofer with Neodymium magnet for improved low frequency response. The speaker shall employ a high quality internal passive crossover circuit with optimized filter slopes and a crossover frequency of 5k Hz. The loudspeaker shall have a smooth frequency response from 100 to 20k Hz. The output sound pressure level at a distance of 1 m with 1 W of input power applied shall be 88 dB SPL. The rated power handling (Continuous Program) shall be 120 W (4 ohms) and 12 W with matching transformer. The loudspeaker shall be compatible with low and high impedance speaker systems and shall include a built-in 70.7/100 V matching transformer with the following selectable tap settings: 12 W, 6 W, 3 W, 1.5 W (70.7 V) and 12 W, 6 W, 3 W (100 V). The speaker shall also have selectable impedance settings of 4 ohms and 16 ohms. The loudspeaker shall include a removable terminal block connector, screw terminal type, with loop-through terminations and accept AWG #14 - #24. An internal protection circuit shall prevent damage to components in an overload condition. Once activated, the circuit shall reduce the input signal and reset automatically after approximately thirty seconds once overload condition is removed. The loudspeaker grille material shall be rolled steel plate (H-2) / stainless steel (H-2WP) with a paintable white finish. The loudspeaker grille frame shall be fire-resistant ABS resin (H-2) / AES resin (H-2WP) with a paintable white finish. Dimensions shall be 10.55" x 4.37” (268 x 111 mm). The speaker shall weight 4.63 lbs. (2.1 kg).

The loudspeaker shall be TOA model H-2 / H-2WP.

請登入以存取更多技術資料，例如軟體、韌體或EASE檔案。

登入

聯絡我們